Poulan 961980025 Instrukcja Użytkownika

OWNER'S MANUALMODEL NUMBER:961980025SNOW THROWER Always Wear Eye Protection During OperationIMPORTANT MANUAL Do Not Throw Away WARNING:Read the

10OPERATIONUSING THE CLEAN-OUT TOOL (See Fig. 15)In certain snow conditions, the discharge chute may be-come clogged with ice and snow. Use the clean-

11OPERATIONTO ADJUST SKID PLATES (See Fig. 17)NOTE: The wrench provided in your parts bag may be used to adjust the skid plates.Skid plates are locate

12OPERATIONCOLD START - ELECTRIC STARTER1. Insert safety ignition key (packed separately in parts bag) into ignition slot until it clicks. DO NOT tu

13GENERAL REC OM MEN DA TIONSThe warranty on this snow thrower does not cover items that have been sub ject ed to operator abuse or negligence. To re

14MAINTENANCEAUGER GEAR CASE• The gear case was filled with lubricant to the proper level at the factory. The only time the lubricant needs attention

15CAUTION: Do not substitute. Use only original equip ment capscrew/shear bolts as sup plied with your snow thrower.4. Connect spark plug wire to spa

16SERVICE AND ADJUSTMENTSWARNING: Belt replacement requires separation of the snow thrower. While separating the auger housing from the frame assembly

17SERVICE AND ADJUSTMENTSSTORAGEImmediately prepare your unit for storage at the end of the season or if the unit will not be used for 30 days or more

18STORAGECYLINDER1. Remove spark plug.2. Pour one ounce (29 ml) of oil through spark plug hole into cylinder.3. Pull recoil starter handle slowly a

19Does not start 1. Fuel shut-off valve (if so 1. Turn fuel shut-off valve to OPEN position. equipped) in OFF position. 2. Safety ignition

2IMPORTANTSafe Operation Practices for Walk-Behind Snow ThrowersThis snow thrower is capable of amputating hands and feet and throwing objects.Failure

20REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inche

21REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)AUGER HOUSING / IMPELLER ASSEMBLYNOTE: All component dimensions given in U.S. inche

22NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

23NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

24REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

25REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)CONTROL PANEL / DISCHARGE CHUTENOTE: All component dimensions given in U.S. inches.

26REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPO

27REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPO

28REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)HANDLESNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPO

29NOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORTANT: Use only Original Equipment Manufacturer (O.E.M.) replacement pa

3CONGRATULATIONS on your purchase of a new snow thrower. It has been designed, engineered and man u fac -tured to give best possible dependability an

30REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORT

31REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORT

32REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)DRIVENOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 mmIMPORT

33REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1

34REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)CHASSIS / ENGINE / PULLEYSNOTE: All component dimensions given in U.S. inches. 1

35REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)WHEELSKEY PARTNO. NO. DESCRIPTION NOTE: All component dimensions given in U.S

36REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)BAG OF PARTSNOTE: All component dimensions given in U.S. inches. 1 inch = 25.4 m

375314217689REPAIR PARTS SNOW THROWER - - MODEL NO. 961980025 (96198002501)DECALSNOTE: All component dimensions given in U.S. inches. 1 inch = 25

38SERVICE NOTES

39SERVICE NOTES

4PARTS PACKED SEPARATELY IN CARTON(1) POWER CORD(198563)(1) DISCHARGE CHUTE(3) RETAINER SPRINGS (169675)(1) TRACTION DRIVE CONTROL ROD(2) SHEAR BOLTS

LIMITED WARRANTYThe Manufacturer warrants to the original consumer purchaser that this product as manufactured is free from defects in materials and w

5ASSEMBLY / PRE-OPERATIONSPEED CON TROL RODSPEED CONTROL BRACKETRETAINER SPRINGSPEED CONTROL LEVERFIG. 2TRACTION DRIVE CON TROL RODDRIVECONTROL BRACKE

6ASSEMBLY / PRE-OPERATIONINSTALL DISCHARGE CHUTE / CHUTE ROTATOR HEAD (See Fig. 7)NOTE: The multi-wrench provided in your parts bag may be used to ins

7OPERATIONKNOW YOUR SNOW THROWERREAD THIS OWNER'S MANUAL AND ALL SAFETY RULES BEFORE OPERATING YOUR SNOW THROWER. Compare the illustrations with

8OPERATIONThrottle/engine control - used to se lect either FAST or SLOW engine speed and to STOP the engine.Traction drive control lever - used to eng

9The operation of any snow thrower can result in foreign objects thrown into the eyes, which can result in severe eye damage. Always wear safety glas