Poulan 3400 Instrukcja Użytkownika

'vJ It/3400 Counter-YlbeCHAINSAWOPERATOR’S MANUALAwARNING:!Carefully read and follow Safety Rules, Precautions and Operating Instructions

F. BAR AND CHAIN OIL• The Guide Bar and Cutting Chain require continuous lubrication In order to remain in operating condition. Lubrication

STARTING INSTRUCTIONS1.BASIC PROCEDUREa. Set the saw on flat ground making certain the saw chain is free tatum without contacting any object. Figure

• Pull-In —— can occur when fhe chain on the bottom of the bar is suddenly stopped.r—pulls the saw rapidly forward.3. PROCEDUREPractice cutting a few

3. FELLING LARGE TREES OR MORE6' DIAMETERThe notch method is used to cut large trees. A notch is cut on the side of the tree i

A WARNINGNever turn the saw upside down to undercut. The saw cannot be controlled in this position.2. TYPES OF CUTTING USED Figure 24:—Overcutting

¿V. WARNINGNever climb into a tree to debranch or prune. Do not stand on ladders, platforms, a log or in any position which can cause you to lose your

A. GUIDE BAR AND CHAINIncrease the service life of your Guide Bar and Chain by:r —Using the saw properly and as recommended in this manual.—Maintaini

b. CHAIN REPLACEMENT1. ) Replace the chain when cutters or linksbreak.2. ) See a qualified service dealer to replaceand sharpen individual cutters

2. SPARKPLUG• Maintenance is indicated when the engine is hard to start.• Keep the spark plug: ^—clean— properly gapped (.025")Items Required:

11.12.13.14.15.16.17.18.Wrap rope counterclockwise aroundpulley ratchet and tuck loose end back under rope leaving a 3/8-1/2 inch tail. Pull tightly

TABLE OF CONTENTSSpecifications .. ... 2SPECIAL SAFETY SECTiON... ЛЛ&5Know Your

CLOCKWISE REMOVE CLUTCHINSTALL CLUTCH COUNTERCLOCKWISE5. Remove the clutch with a 3/4" socket or end wrench maclockwise direction. Figure 48.Figu

CAUTION:I Never set the High Speed Mixture Screw less than 7/8 turn open. This is too lean a setting and will damage your engine.6. IDLE SPEED

I. TROUBLE SHOOTING CHARTTROUBLECAUSEREMEDYENGINE WILL NOT START1. ignition Switch off.2. Fuel tank empty.3. Spark Plug not firing.4. Fuel not re

J. MAINTENANCE CHARTr<o5^ COc -S'ic OJsà^ o^ iQ.o-C wO 0>« cZ <D 0) 3>v5coE-S’ B -TJCDO)CD£(0TJ1*3cr2COCDCDO)CDO-CDCOComplete machi

PARTS LISTA. ILLUSTRATION and DESCRIPTION 124KEVPARTKEYPARTKEYPARTDESCRIPTIONNO. NO.QTV.DESCRIPTIONNO.NO.QTY.DESCRIPTIONNO.NO.QTY.1 390951Flywheel Ass

в. ILLUSTRATION and DESCRIPTION 2KEYNO.PARTNO. ОТУ.DESCRIPTIONKEYNO.PARTNO.OTY,DESCRIPTIONKEYNO.PARTNO.QTY.DESCRIPTK9N1243766Cu(>*lsol3t0r1732053Bu

с. ILLUSTRATION and DESCRIPTION 3KEYNO.PARTNO.QTY,DESCRIPTIONKEYNO.PARTNO.QTY. DESCRIPTIONKEYNO.PARTNO.QTY. DESCRIPTION1 ^69171 1 Kit-Grip-Handleba

D. CARBURETOR ASSEMBLY #35094KEYNO.PARTNO.QTY.DESCRIPTION1 351151- Screw-PumpCover2 350991Cover- Fuel Pump3 351091Gasket- Fuel Pump4350691‘Screen-Inle

PARTS AND SERVICEYour Beaird-Poulan/Weed Eater product has been expertly engineered and carefully manufactured to rigid quality standards/As with all

SPECIAL SAFETY SECTIONGUARD AGAINST KICKBACKKickback is a dangerous reaction that can lead to serious personal injury. Do not rely only on the sdfety

SPECIAL SAFETY SECTION (continued)I. WARNINGBecause a chain saw is a high-speed wood-cutting tooi, special safety precautions must be observed to r

OPERATE YOUR SAW SAFELY1. Do not operate a chain saw that is damaged, improperly adjusted, or not completely and securely assembled.2. Opera

KNOW YOUR CHAIN SAWA. INTRODUCTION ^• Your saw has been designed with safety in mjnd and includes the following features as standard equipment:-Reduc

PREPARING YOUR SAW FOR USEA. GETTING READY1. READ YOUR OPERATOR’S MANUALYour Operator’s Manual has been developed to help you prepare your

2. Mount the Guide Bar with the slotted end over the bar mounting studs. Figure 9 .NOTE: Be sure the Guide Bar is positioned with the r

E. ENGINE FUEL MIXTURE• Your chain saw is powered by a two-cycle engine which requires a fuel mixture of regular^asoline (leaded or unleaded) and a h