Poulan 1600 Instrukcja Użytkownika

^ ^ : ; >^:V-ii-Oi-:;-;"- :-vi i:-'. -I;TRADEMARK®OPERATOR’SMANUAL:AWAJtNlNG: Read the Operator’s Manual and Follow All Warn

в* PRE-OPERATION CHECKS AwarningReview all Warnings and Safety Instructions in this manual.Before operating your tool, always:1. Inspect the

D. OPERATING INSTRUCTIONS1. Bring the engine to cutting speed before entering the materiai to be cut.a. Do not run the engine at a higher sp

A. LINE TRIMMER SAFETY1, OPERATORa. Always wear a safety face shield or goggles. See“Accessories”b. Always wear heavy, long pants, boots and gloves

C. CUTTING METHODS• The tip of the line does the cutting. Allow the 1 i ne totrim at its own pace. You will achieve better results by not crowding t

GENERAL MAINTENANCEA. MAINTENANCE SAIVrrYI. Maintain the tool according to recommended procedures. Keep the trimmer line at the proper length.

e. Make sure the line saver is in place and installed correctly, then insert the end of the line in the line saver as shown in Figure 18. Place spool

с. CARBURETOR ADJUSTMENTS^WARNINGMake carburetor adjustments with the driveshaft housing supported to prevent the trimmer line from con

4.1>ECEjUE;RAT10N CHECKa. Allow engine to idle, then squeeze Throttle Trigger fully.b. Allow engine to mn at full speed for about 1 second.c. Re

£. STARTER ROPE• This is a complicated and potentially hazardous task. It is recommended Uiat only a qu^ifled service dealer perform th

j cAUTlO?^ Before replacing the fan housing, make certain that the ‘‘off” button temunal on the ignition module is not bent. See insert,

TABLE OF CONTENTSWARNINGS AND SAFETY INSTRUCTIONS... 3KNOW YOUR TRIMMER... 6ASSEMBLY...

PARTS LISTA.IjOWERUNITAwarningAll repairs, adjustments and maintenance not described in the Operator’s Manual must be performed by a qualified service

в. POWER UNIT - ILLUSTRATION123>122-^:::::^2417\pngïnê^/Gasket/ - >^л1 102\^Саг^/" /Repair / Kit \Caity^/Gasket/ -.Kit -Л12512622

C. POWER UNIT ^ DESCRIPTIONKEYNO.PARTNO.QTY.REQ.DESCRIPTIONKEYNO.PARTNO.QTY.REQ.DESCRIPTION1107291Fuel CapAssembiy (incl. 0-Ring)65 271001Cover-Carbur

G. TROUBLE SHOOTING CHARTTROUBLECAUSEREMEDYEngine will not start1. Fuel tank empty.1. Fill tank with correct fuel mixture.or will run only for2. Engin

PARTS AND SERVICEYom Poulan® / Weed Eater® product has been expertly engineered and carefully manufec- tured to rigid quality standard

Awarnings and safety instructionsA'WASLHISG^TtmPOWERTOOLCANBEDANGEROUS!This tool can cause serious injury or blindness to the operator and others

NOTES

^WARNINGS AND SAFETY INSTRUCTIONS (Contitiued)A OPERATOR SAFETY1. Alwa^^s wear a safety face shield or goggles. See “Accessories.”2. Always wear heav

KNOW YOUR TRIMMERA. INTRODUCTIONYour Trimmer is a versatile product developed for large lawns and io make short work of a variety of lawn care tasks

ASSEIVEBUV received assembled, repeat all steps in this section to be sure assembly is correctand is adjusted for the operator.)A. PREPARATIONThis Op

3.SH1ELD ^ Figure 4AwarningFailure to instaU theshieid in the positionshovm in Figure 4 and 5 can result in serious inj ury to the

ENGINE INFORMATIONA. FUELING YOUR ENGINE1. FUEL SAFETYa. Use only recommended fuel mixtures.b. Mix and pour fuel outdoors and where there ar